PB520 Main Setup Menu

Press <F1> during post to get into setup. This is an example only; actual configuration may vary.

All default values shown below are subject to change.


Configure With BIOS Default Menu Option

Load BIOS Setup Default Values From ROM Table (Y/N) ?
Enter "N" to not load the BIOS setup default values.
Enter "Y" to load the BIOS setup default values.



Configure with Power On Default Menu Option

Load Power-On Default Values From ROM Tables (Y/N) ?
Enter "N" to not load the Power-On default values.
Enter "Y" to load the Power-On default values.



Change Password Menu Option

NOTE:

This option will always be labeled "Change Password", even if there is no current password.

A. ENTERING A NEW PASSWORD 

                         ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"	
                         º                        º	
                         º  Enter New Password :  º	
                         º                        º	
                         ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4	

                       ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"	
                       º                           º	
                       º  Re-Enter NEW Password :  º	
                       º                           º	
                       ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4	

                         ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"	
                         º                        º	
                         º  Password Now Enabled  º	
                         º                        º	
                         ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4
B. CHANGING AN EXISTING PASSWORD

NOTE:

To disable a password:
1. Enter the current password.

2. When asked for the new password just press <Enter>. 

                        ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"
                        º                         º
                        º Enter CURRENT Password: º
                        º                         º
                        ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4

                         ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"
                         º                        º
                         º  Enter New Password :  º
                         º                        º
                         ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4

                       ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"
                       º                           º
                       º  Re-Enter NEW Password :  º
                       º                           º
                       ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4

                         ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"
                         º                        º
                         º  Password Now Enabled  º
                         º                        º
                         ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4
Enter "Y" and press <<ENTER>> to write the changes to CMOS and exit.
Enter "N" and press <<ENTER>> to cancel this operation.



Do Not Write to CMOS and Exit Menu Option

                 ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ"	
                 º                                       º	
                 º Want to Quit Without Saving (Y/N) ? N º		
                 º                                       º
                 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4
Enter "Y" and press <<ENTER>> to exit without saving.
Enter "N" and press <<ENTER>> to cancel this operation.



Standard CMOS Setup Menu




Drive Type

Auto-Config BIOS automatically senses hard drive and configures it.
User Type 1/2 User definable parameters for drives not supported by Auto-Config.



Drive Time-out

The amount of time the system will allow Auto-Configuring for an IDE drive before generating an error.



Keyboard

Disabled
Enabled



Advanced CMOS Setup Menu



Typematic Rate Programming

Disabled
Enabled Allows the typematic rate options to be used.



Typematic Rate Delay (msec)

250/500/750/1000 Default is 500. Determines how long it takes for the key repeat function to start when a person is holding down a key on the keyboard.



Typematic Rate (char/sec)

6/8/10/12/15/20/24/30 Default is 15. Determines the speed at which characters repeat when you hold down a key on the keyboard. The higher the number, the faster the characters repeat.



Press <F1> Message Display

Enabled
Disabled



System Boot Up Numlock

On
Off



System Boot-Up Sequence

A:, C:
C:, A:
C: only



System Boot-Up CPU Speed

High
Low



Cache Memory

Enable Enables secondary cache.
Disable



Network Password Checking

Enable
Disabled
Prompts for password when logging onto a network. To enable this option, you must also enable the "Change Password" option.



Set Linear Frame Buffer

1/2/4 MB
Disabled.
For use with ISA Video cards that use a linear frame buffer. This speeds up video performance, since the image data is retrieved directly from the buffer.

NOTE:

(The memory allocated by this option is always taken from system memory starting at 16 MB downward. The amount taken s double the amount selected. For example, if 2 MB is selected, the memory from 16 MB down to 12 MB (a total of 4 MB) will be allocated. On a system with 16 MB of memory, the memory from 16 MB down to 12 MB will be used for the linear frame buffer, but a system with less then 12 MB will not lose any memory.)



Set Linear Frame Address

15/14/12 MB Automatically set when linear frame buffer is set.



Disable Shadow Memory Size

16/32/48/64 KB

Disabled Disable Shadow Memory Base

C0000H/C4000H/C8000H/CC000H/D0000H/D4000H/D8000H/DC000H

NOTE:

(Alters the location of the BIOS that is not shadowed. The amount of BIOS that is not shadowed is less for addresses greater than D0000H.)



Base Memory Size

640 KB
512 KB



IDE DMA Transfer Mode

Disabled
Standard Compatible.
Type B Drive must support this to work.
Type F Fastest - Drive must support this to work.



IDE DMA Multiple Sector Mode

Disabled
1/2/4/8/16/32/64 S/B Read/Write Multi.



IDE LBA Translations

Enabled Enable Logical Block Addressing.
Disabled



Enhanced ISA Timing

Enabled ISA bus will run at 10 MHz (this could be too fast for some cards).
Disabled ISA bus will run at 8 MHz.



ISA IRQ 9

Free No ISA cards are using this IRQ.
Used An ISA card is using this IRQ.



ISA IRQ 10

Free No ISA cards are using this IRQ.
Used An ISA card is using this IRQ.



ISA IRQ 11

Free No ISA cards are using this IRQ.
Used An ISA card is using this IRQ.

Peripheral Management Setup Menu |0| 3-10-95/MBT/PB520SET



Programming Option

Auto System peripherals are automatically configured during power up.
Manual The additional settings in this menu must be explicitly configured.

On-Board Floppy Drive

Enabled
Disabled

On-Board IDE Drive

Enabled
Disabled

Serial 1 (Internal Header)

Disabled
2E8H/3E8H/2F8H/3F8H If "Programming Option" is set to "AUTO" then this is 3F8H.

Serial 2 (External DB9)

Disabled
2E8H/3E8H/2F8H/3F8H If "Programming Option" is set to "AUTO" then this is 2F8H.

Parallel Port Address

Disabled
278H/378H/3BCH If "Programming Option" is set to "AUTO" then this is 378H.

Parallel Port Mode

Normal Unidirectional (AT mode).
Extended Bidirectional (PS/2 mode).



CMOS Setup Warning Menu

NOTE:

This screen appears when entering the "Standard CMOS Setup", "Advanced CMOS Setup", and "Peripheral Management Setup" menus.