PB520R Setup Screens

Press <F1> during post to get into setup. The following setup screens are samples only.

PB520R SETUP SCREEN (Version 1.00.01)
PB520R SETUP SCREEN (Version 1.00.02 or newer)

PB520R Original Setup Screen

Standard CMOS Setup

Advanced CMOS Setup

Peripheral Management Setup

Floppy Drive A: / B:
Disabled.
360 KB, 5 1/4".
1.2 MB, 5 1/4".
720 KB, 3 1/2".
1.4 MB, 3 1/2".
2.88 MB, 3 1/2".
Drive Type
Auto-Config BIOS automatically senses hard drive and configures it.
User Type 1/2 User definable parameters for drives not supported by Auto-Config.
Drive Timeout
0/5/10/20 sec. The amount of time system allows for Auto- Configuring an IDE drive before generating an error.
Keyboard
Disabled
Enabled
Typematic Rate Programming
Disabled
Enabled Allows the typematic rate options to be used.
Typematic Rate Delay (msec)
250/500/750/1000
Default is 500.- Determines how long it takes for the key repeat function to start when a person is holding down a key on the keyboard.
Typematic Rate(chars/sec)
6/8/10/12/15/20/24/30
Default is 15. - Determines the speed at which characters repeat when you hold down a key on the keyboard. The higher the number, the faster the characters repeat.
Press <F1> Message Display
Enabled
Disabled
System Boot Up Numlock
On
Off
System Boot Up Sequence
A:, C:
C:, A:
C: only
System Boot Up CPU Speed
High
Low
Cache Memory
Enable Enables secondary cache.
Disable
Network Password Checking
Enable
Disabled Prompts for password when logging onto a network.To enable this option, you must also enable the "Change Password" option.
Set Linear Frame Buffer
1/2/4 MB
Disabled For use with ISA Video cards that use a linear frame buffer. This speeds up video performance, since the image data is retrieved directly from the buffer.
(NOTE: The memory allocated by this option is always taken from system memory starting at 16 MB downward. The amount taken is double the amount selected. For example, if 2 MB is selected, the memory from 16 MB down to 12 MB (a total of 4 MB) will be allocated. On a system with 16 MB of memory, the memory from 16 MB down to 12 MB will be used for the linear frame buffer, but a system with less then 12 MB will not lose any memory.)
Set Linear Frame Address To
15/14/12 MB Automatically set when linear frame buffer is set.
Disable Shadow Memory Size
16/32/48/64 KB
Disabled
Disable Shadow Memory Base
C0000H/C4000H/C8000H/CC000H/D0000H/D4000H/D8000H/DC000H

Note:

Alters the location of the BIOS that is not shadowed. The amount of BIOS that is not shadowed is less for addresses greater than D0000H.)
Base Memory Size
640 KB
512 KB
IDE DMA Transfer Mode
Disabled
Standard Compatible.
Type B Drive must support this to work.
Type F Fastest - Drive must support this to work.
IDE DMA Multiple Sector Mode
Disabled
1/2/4/8 Read/Write Multi.
16/32/64 Sectors.
IDE LBA Translations
Enabled Enables Logical Block Addressing.
Disabled Bypasses Pre-delay.
Enhanced ISA Timing
Enabled ISA bus will run at 10 MHz (this could be too fast for some cards).
Disabled ISA bus will run at 8 Mhz.
ISA IRQ 9
Free No ISA cards are using this IRQ.
Used An ISA card is using this IRQ.
ISA IRQ 10
Free
Used
ISA IRQ 11
Free
Used
Programming Option
Auto System peripherals are automatically configured during power up.
Manual The additional settings in this menu must be explicitly configured.
On-Board Floppy Drive
Enabled
Disabled
Configuration Mode
Auto Configured
User Definable
On-Board IDE Drive
Enabled
Disabled
First Serial Port Address
Disabled
2E8H/3E8H/2F8H/3F8H If "Programming Option" is set to "AUTO" then this is 3F8H.
Second Serial Port Address
Disabled
2E8H/3E8H/2F8H/3F8H If "Programming Option" is set to "AUTO" then this is 2F8H.
Parallel Port Address
Disabled
278H/378H/3BCH If "Programming Option" is set to "AUTO" then this is 378H.
Parallel Port Mode
Normal Unidirectional (AT mode).
Extended Bidirectional (PS/2 mode).

PB520R Revised Setup Screen

NOTE:

Press <F1> during post to get into setup. This is an example only; actual configuration may vary.

PB520R Hard Disk C: Sub-Menu

PB520R Hard Disk D: Sub-Menu

PB520R Hard Disk E: Sub-Menu

PB520R Hard Disk F: Sub-Menu

PB520R Boot Option Sub-Menu

PB520R Advanced Setup Menu

PB520R Peripheral Configuration Menu

PB520R Advanced Chipset Configuration Menu

PB520R Advanced Power Management Configuration Menu

PB520R Plug-N-Play Configuration Menu

PB520R Exit Menu

PB520R Security Menu

Setup User Password


NOTE:

Press <F1> during post to get into setup. This is an example only; actual configuration may vary.

Setup Administrative Password


Initialization Timeout
Disabled
5 Seconds
10 Seconds
31 Seconds
Translation Modes
Standard CHS
Logical Block
Extended CHS
Auto Detect
Multi Sector Setting
Disabled
4 Sectors/Block
8 Sectors/Block
Auto Detected
PIO Modes
Disabled
Auto Detected
Setup Prompt
Enabled
Disabled
Hard Disk Pre-Delay
Disabled
1 Second
2 Seconds
3 Seconds
4 Seconds
5 Seconds
6 Seconds
7 Seconds
PCI IDE Interface
Enabled
Disabled
Parallel Port Mode
Compatible
Extended
Byte Merging
Enabled
Disabled
ISA LFB Size
Disabled
1 MB
3 MB
7 MB
Video Pallete Snoop
Enabled
Disabled
Latency Timer (PCI Clocks)
0 - 255 (Enter Manually)
Advanced Power Management
Enabled
Disabled
IDE Power Down
Enabled
Disabled
Video Power Down
Enabled
Disabled
Inactivity Timer
0 - 255 (Entered Manually)
Hot Key
A - Z (Entered Manually)
Floppy Interface
Enabled
Disabled
Serial Port 1, 2 IRQ
Enabled
Disabled
IRQ 5, 9, 10, 11
Available
Used
Parallel Port IRQ
Enabled
Disabled
Configuration Mode
Use Setup Utility
Use ICU
ISA Shared Memory Size
Disabled
16 KB
32 KB
48 KB
64 KB
User Password
Enabled
Disabled
Administrative Password
Enabled
Disabled

Set User Administrative Password

NOTE:

To disable a password:

1. Enter the current password.

2. When asked for the new password just press <Enter>.


Exit Saving Changes
Enter to confirm, ESC to abort
Exit Discarding Changes
Enter to confirm, ESC to abort
Load Setup Default
Enter to confirm, ESC to abort
Discard Changes
Enter to confirm, ESC to abort